Polskie Forum FPV

klocolus pisze: Na razie regulamin by się przydał.

Ok...zaraz zrobie w pierwszym poscie (tematu o zawodach na 1mW)
Jesli o czyms zapomnialem/przeoczylem/niedopowiedzialem....to dajcie znac.....

eLeReS test 1

Micro mode (1mW) + tłumik 20db czyli razem 0.01mW. Bez problemu mogę obejść całe mieszkanie.

W skrajnych pokojach przez trzy ściany także daje radę

eLeReS test 2

Micro mode + tłumik 20db (w sumie 0.01mW), spacer po ziemi. W linii prostej na osiedlu udało się przejść ok. 100m, sygnał przez krzaki, odbiornik nie może się zdecydować którą diodę wybrać - link oczywiście jest. Anteny na wysokości około 1m nad ziemią. Jakby nie mówić w terenie mocno zabudowanym.

CO według kalkulacji daje minimum 1,5km w micro mode podczas lotu. Polatamy zobaczymy

Czekam Karol na loty !! ;)

Może przestanę byc samotny w dziale konkursowym ;) a i zamkną się paszcze wszystkim niedowiarkom ;)

Czekam Karol na loty !! ;)

Lot będą dopiero za jakoś czas - teraz mam inny priorytet.

Spokojnie, konkurs trwa jeszcze długo

jak nie polecę na 1W z vee w nadajnikju 20km zapinam SuperYagode

Zapewniam Cie, ze na 1mW (i to jeszcze z tlumikiem!) z taka antena polecisz >20km!
(btw...ale w konkursie 1mW...takie anteny sa fuj )

Dokładnie! Rozmawiałem z gościem, który odbierał dane swoją radiostacją z balonu meteo na wys 22km, rfm22b nadawał na 10mW i miał zasięg w lini prostej od siebie ponad 150km. Na pełnej mocy tego modułu nawiązał połączenie ze Słowacją, ale TX też był dość wysoko.

hello

i'am trying to setting up the eleres TX and RX module
al power connections went good i had the red and green led's burning now when i trying to binding the tx and the rx what i not can find out wath i do wrong i don't understand the manual on the site

now after a time the RX wond not power on anymore i get no burning led's anymore
the battery is good the conections are fine but i can not power on my rx module anymore

the batt was a 2s 480mAh

for sure it's not a easy system the eleres

al firmware flashing was succsefuly

nicky1980 pisze:hello

i'am trying to setting up the eleres TX and RX module
al power connections went good i had the red and green led's burning now when i trying to binding the tx and the rx what i not can find out wath i do wrong i don't understand the manual on the site

now after a time the RX wond not power on anymore i get no burning led's anymore
the battery is good the conections are fine but i can not power on my rx module anymore

the batt was a 2s 480mAh

for sure it's not a easy system the eleres

al firmware flashing was succsefuly

Hi

I've sent you an email requesting more details - please kindly respond ant we'll try to figure out what is wrong.

Regards
Maciej

done

sended yesterday a couple of mails
thanks for the reply

qqror pisze:

nicky1980 pisze:hello

i'am trying to setting up the eleres TX and RX module
al power connections went good i had the red and green led's burning now when i trying to binding the tx and the rx what i not can find out wath i do wrong i don't understand the manual on the site

now after a time the RX wond not power on anymore i get no burning led's anymore
the battery is good the conections are fine but i can not power on my rx module anymore

the batt was a 2s 480mAh

for sure it's not a easy system the eleres

al firmware flashing was succsefuly

Hi

I've sent you an email requesting more details - please kindly respond ant we'll try to figure out what is wrong.

Regards
Maciej

Nicky...this is the main thread of eleres: http://rc-fpv.pl/viewtopic.php?t=5202&p ... start=3210
Plz, write there next time....

mifau pisze:Nicky...this is the main thread of eleres: http://rc-fpv.pl/viewtopic.php?t=5202&p ... start=3210
Plz, write there next time....

o sorry
thanks for the link
but it's dificult to search en understand here the polich also wen it translated with google

i think the RX module is dead :( i'dont know wath i did wrong, i'am realy sure that i not connected the powering wrong, i think that it is becouse fingerprints on the module electronic parts soldered on the model if you understand what i mean

i'am sure that the system is nice but it's realy not a plug and play and i'am not a elektronic and program expert

hope somone can help me if it not working anymore that it's over for me and the eleres
it's regrettable for the money i spendet on the eleres rather than as more losses on a new module

sorry for my bad english

Gentlemens, this is a Polish forum and also write the language.
Nicky1980 can use the google translator. or go to a RCG. is in english
A moderator where it sits? Afraid to speak up and punish violators rules and netiquette

Gentlemens, this is a Polish forum

So what? We're not nationalists here. If we were, you'd be first to go - you are from UK, traitor

Nicky1980 can use the google translator.

We both know how inaccurate this thing is. As for me - I prefer to read his posts even in chinglish than in botched attempts to translate that to Polish.

or go to a RCG.

...and who are you to tell him (or anyone else) to go away? Admin or something? He is welcomed here as much as you.

Nicky - go to proper thread as indicated by Mifau, post some pictures or video of your problem and I'm sure we can work something out.

Verid pisze:

Gentlemens, this is a Polish forum

So what? We're not nationalists here. If we were, you'd be first to go - you are from UK, traitor

Nicky1980 can use the google translator.

We both know how inaccurate this thing is. As for me - I prefer to read his posts even in chinglish than in botched attempts to translate that to Polish.

or go to a RCG.

...and who are you to tell him (or anyone else) to go away? Admin or something? He is welcomed here as much as you.

Nicky - go to proper thread as indicated by Mifau, post some pictures or video of your problem and I'm sure we can work something out.

thanks mate

i did posted some pics in that tread

and sorry i can not understand Polish nowone is perfect