Na które kanały miałeś ustawione wypluwanie sygnału z DIY HT ?Adrián pisze:Uzywałem również diy ht z kubłami i wszystko z taranisem x9d.
Przepraszam że dopiero dzisiaj odpisuję ale jestem na zlocie w Konarzynach i dzisiaj dopiero znalazłem chwilę żeby siąść do komputera.pawelsky pisze:@PiotrSz, a pokaz co masz w config.h
Kod: Zaznacz cały
//-----------------------------------------------------------------------------
// File: Config.h
// Desc: Compilation configuration file. Defines user-configurable settings
// as well as project-wide development #defines for configuration.
//-----------------------------------------------------------------------------
#ifndef config_h
#define config_h
//-----------------------------------------------------------------------------
// These are things you can change before you compile, to enable/disable
// features.
//
// Set to 1 to enable PPM input, 0 to disable.
#define PPM_IN 0
// Button hold time for pause/unpause
#define BUTTON_HOLD_PAUSE_THRESH 1500 // 1.5 second button hold required to pause/unpause tracking.
// Set to 1 to enable support for positive shift PPM equipment, 0 for negative.
#define POSITIVE_SHIFT_PPM 1
// Fatshark headset headtracker module support. Set to 1 to enable.
// See: http://www.rcgroups.com/forums/showpost.php?p=23051198&postcount=573
#define FATSHARK_HT_MODULE 0
//
// -- End of user-configurable parameters.
//-----------------------------------------------------------------------------
//=============================================================================
//-----------------------------------------------------------------------------
// The user generally won't need to touch any of the following
//
// Firmware Version, e.g. X.YY
#define FIRMWARE_VERSION_FLOAT 1.04 // 2 decimal places
// Number of PPM channels out. 1 - 12 channels supported.
#define NUMBER_OF_CHANNELS 8
// Define for extra debug serial info
#define DEBUG 0
// Output serial data to host evern X frames
#define SERIAL_OUTPUT_FRAME_INTERVAL 10
// Serial communication speed.
#define SERIAL_BAUD 57600
// Sensor board update-rate. Not done yet.
#define UPDATE_RATE 50
// Dead-time between each channel in the PPM-stream.
#define DEAD_TIME 800
// Sets the frame-length .
#define FRAME_LENGTH (5003 + NUMBER_OF_CHANNELS * 5000)
// TOP (timer rollover) used for PPM pulse time measurement
#define TOP (5003 + NUMBER_OF_CHANNELS * 5000)
// Set to 0, stored gyro calibration is used. If 1, gyro is calibrated at powerup
#define ALWAYS_CAL_GYRO 0
// Center/pause input button pin number
#define BUTTON_INPUT 11
// Arduino LED
#define ARDUINO_LED 13
// Pin definition for LED and buzzer (Fatshark goggles)
#if FATSHARK_HT_MODULE
#define BUZZER 4
#endif
#define PPM_IN_MIN 1000 // 0.5 ms
#define PPM_IN_MAX 4000 // 2 ms
// Settings stuff
//
#define HT_TILT_REVERSE_BIT 0x01
#define HT_ROLL_REVERSE_BIT 0x02
#define HT_PAN_REVERSE_BIT 0x04
#endif
Kod: Zaznacz cały
//-----------------------------------------------------------------------------
// File: Config.h
// Desc: Compilation configuration file. Defines user-configurable settings
// as well as project-wide development #defines for configuration.
//-----------------------------------------------------------------------------
#ifndef config_h
#define config_h
//-----------------------------------------------------------------------------
// These are things you can change before you compile, to enable/disable
// features.
//
// Set to 1 to enable PPM input, 0 to disable.
#define PPM_IN 0
// Button hold time for pause/unpause
#define BUTTON_HOLD_PAUSE_THRESH 1500 // 1.5 second button hold required to pause/unpause tracking.
// Set to 1 to enable support for positive shift PPM equipment, 0 for negative.
#define POSITIVE_SHIFT_PPM 1
// Fatshark headset headtracker module support. Set to 1 to enable.
// See: http://www.rcgroups.com/forums/showpost.php?p=23051198&postcount=573
#define FATSHARK_HT_MODULE 0
//
// -- End of user-configurable parameters.
//-----------------------------------------------------------------------------
//=============================================================================
//-----------------------------------------------------------------------------
// The user generally won't need to touch any of the following
//
// Firmware Version, e.g. X.YY
#define FIRMWARE_VERSION_FLOAT 1.04 // 2 decimal places
// Number of PPM channels out. 1 - 12 channels supported.
#define NUMBER_OF_CHANNELS 8
// Define for extra debug serial info
#define DEBUG 0
// Output serial data to host evern X frames
#define SERIAL_OUTPUT_FRAME_INTERVAL 10
// Serial communication speed.
#define SERIAL_BAUD 57600
// Sensor board update-rate. Not done yet.
#define UPDATE_RATE 50
// Dead-time between each channel in the PPM-stream.
#define DEAD_TIME 800
// Sets the frame-length .
#define FRAME_LENGTH (5003 + NUMBER_OF_CHANNELS * 5000)
// TOP (timer rollover) used for PPM pulse time measurement
#define TOP (5003 + NUMBER_OF_CHANNELS * 5000)
// Set to 0, stored gyro calibration is used. If 1, gyro is calibrated at powerup
#define ALWAYS_CAL_GYRO 0
// Center/pause input button pin number
#define BUTTON_INPUT 11
// Arduino LED
#define ARDUINO_LED 13
// Pin definition for LED and buzzer (Fatshark goggles)
#if FATSHARK_HT_MODULE
#define BUZZER 4
#endif
#define PPM_IN_MIN 1000 // 0.5 ms
#define PPM_IN_MAX 4000 // 2 ms
// Settings stuff
//
#define HT_TILT_REVERSE_BIT 0x01
#define HT_ROLL_REVERSE_BIT 0x02
#define HT_PAN_REVERSE_BIT 0x04
#endif
Nie ma problemu, ciesze sie ze dzialaPiotrSz pisze:Przepraszam że dopiero dzisiaj odpisuję ale jestem na zlocie w Konarzynach i dzisiaj dopiero znalazłem chwilę żeby siąść do komputera.
[...]
Edyta: Temat ogarnięty, pomogło ponowne załadowanie softu i HT zaczął działać jak trzeba.
Musialbys najpierw pogadac z AE_, hangarspace czy kto tam teraz najaktywniej zajmuje sie tym projektem o dodanie komunikacji z BT FrSky.piotr pisze:FrSky udostępnia bezprzewodową komunikację portu trenera .Czy w związku z powyższym nie można połączyć bezprzewodowo HT?